MINIJAZZ - SMALL BUT POWERFUL

The small MINIJAZZ convinces you with lots of functions. Its size is only 36x20 mm but he includes all well known JAZZ features; so the really good RPM control and starting sequence.

The MINIJAZZ hat the same mode programming as all JAZZ ESC’s and is therefore well prepared for really all applications.

Where space and weight is sensitive and lost of performance is not acceptable, there the MINIJAZZ is just right.

For its size the MINIJAZZ has a strong BEC and is so prepared especially for small helicopters like T-Rex 250

The KONTRONIK MINIJAZZ is available with the following specifications:

JAZZ THE INTELLIGENT POWER HOUSE

All JAZZ ESCs are equipped with a BEC up to 6 S LiPo (25 V). Even the most skeptical of pilots have become fully satisfied after the first flight. A new high level electronic circuit was developed to create a strong BEC without the well-known interference problems.

The excellent suppression of interference makes the optocoupler unnecessary. This was improved on our own EMV test bench.

Helicopter pilots like its sensitive RPM control and its easy-to-use programming. Due to the integrated BEC the helicopter saves on weight.

Due to the 6 layer assembly of the PCB board with 1 mm copper the JAZZ ESCs keep cool” even during long flights or in high power applications.

These are only a few features which make the JAZZ a leading product. You can be sure that JAZZ will convince you like thousands of other modellers before you.

The KONTRONIK JAZZ is available with the following specifications:

SUN - KONTRONIKS NEW SUNSHINE

The Mode Programming System of the SUN PLUS line allows (to select) selection of an operating mode, which updates all controllable settings to optimal values. There is no need to program each ESC setting one after another– such as EMF brake, maximum RPM or under voltage cut off. Instead, you need only to select the area of use of your model.

Another essential highlight of the SUNs is the protection against reversal polarity. If plus and minus are changed when connecting the battery, no damage will happen.
As a matter of course the SUNs have an integrated LiPo Mode which programs all the necessary changes in the ESC when using LiPo batteries.

The Heli Mode provides an Automatic Power Compensation. APC is a KONTRONIK development and is only available in SUN PLUS ESCs. It compensates the decreasing battery voltage by increasing the motor current. In the Heli Mode, most protection circuits are deactivated. No unwelcome cut-off can risk flight security.

Also, there is an integrated RC-Car Mode which offers a proportional brake for precise braking and an immediate throttle response for fast acceleration.

The programming of the SUN PLUS ESCs can also be done by PROGCARD which allows adjustment of all specs on the flying field without an additional PC.

Due to the 2 A BEC all SUN PLUS capacitate an adequate supply of max. 4 servos.
SUN PLUS ESCs come with the active free-wheeling circuit which means they have a full part load capability.

The under voltage disconnection is automatically calculated when the battery pack is connected to the ESC.

The performance and integrity of the unit are maintained by intelligent protection features. By measuring the temperature of the ESC, power to the motor is reduced if an overload is detected.

The KONTRONIK SUN is available with the following specifications:

KONTRONIK CONNECTOR SYSTEM

The KONTRONIK high performance connector system is made from silver-plated brass, meeting all the requirements for a good connector system:

Low contact resistance – Silver-plating with a brass cross-section for an excellent electrical conductivity.

Extremely light-weight – Connectors are hollow for a reduced weight.

Good Solderability – Unique soldering post for lengthwise or crosswise orientation of cable.

Low weight, small size and safe contact make it what it is – a connector system useful for
competition. It is often used at world championships.

TORODIAL CORE

Tolerances in your RC equipment may cause glitches and can decrease the range of your transmitter.

KONTRONIK has approached this problem, and after thorough research and testing we have selected this special filter, built from a nanocrystalline substance.

The torodial core, used with the JAZZ ESCs, is available as an accessory.

AERONAUT PROPELLERS

High-performance Aeronaut propellers are completely CAD-designed.

Reinforced with carbon fiber, they have tremendous strength and efficiency.

Thus the KONTRONIK idea of offering a complete drive comes true.

Available sizes: from 12 x 8 inches to 17 x 11 inches

PROGCARD

KONTRONIK now offers a small, easy-to-use programming tool, the PROGCARD.

With this card you can modify every single function of all ESCs, which are especially prepared forPROGCARD programming.

It does not matter if it is the brake, the LiPo Mode or the stick positions. Each function can be easily programmed by a push on the button. LEDs show you the actual settings. No separate battery or an additional computer is necessary.

The PROGCARD II allows a differentiation of the settings of the unique features of the JIVE ESCs. You can se it as intuitively as the PROGCARD. Even complex vernier adjustments are simple and clearly arranged.

KONTRONIK PROGCARD is available in two versions:

PLANETARY GEAR

The KPG25, as used on our KIRA drives, is also available as an accessory and can be mounted on all motors with a 3.17 mm shaft, using an adaptation flange.

The KPG25 is maintenance-free and available with the gear ratio 5.2:1. The KPG25 gear box includes the planets with needle bearing, the oil filling and the motor pinion. The motor pinion has to be glued to he motor with a Loctide adhesive (e.g. 648). The adhesive can be dissolved by administering heat, for instance, when needing to change the gear ratio.

Of course, the needle-mounted planets are included in delivery and the gear box is already lubricated.

The fitting adaptation flange must be ordered separately, whenever a direct drive is changed to a geared one.

ADAPTION FLANGES

Extend the versatility of KONTRONIK KIRA Motors

The fitting adaptation flange must be ordered separately, whenever a direct drive is changed to a geared one.

To adapt the KPG25 to other motors flanges of three different sizes are available.